Chevy Nova Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 37 Results
  1. Body and Interior
    Looking for an OEM or reproduction steering wheel that is similar to the one used in a 66. Anyone out there have what I need? Thanks, Tony
  2. Ebay, etc. Discussion
    Found this whilst browsing Craig's list. They have other parts available apparently. https://sacramento.craigslist.org/pts/d/newcastle-nova-steering-column-1966/7376682776.html Hope someone can use these! :) ~Andy
  3. 1962-67 Chevy II parts
    I have a 63 coupe that I am pulling the original 194, It does run but has some issues I will also be removing stock control arms, front drums, springs, shocks and steering I will not monitor this page for replies, want anything send me a PM $500 for all of it,,,just cause we need to put a price
  4. Steering, Suspension, and Chassis
    My son wanted to change his steering wheel out on his 77 nova Concorse and when he was taking it apart the upper steering column bearing went out. After research and thanks to help from here I finally found one and replaced it to stop the movement from back and forth and side to side. NOW once...
  5. Steering, Suspension, and Chassis
    Hello, its that newbie with the leaks 😄. My turn signal was all loose and wobbly, cracked and it honked my horn every 2 seconds. So I replaced it. The replacement went well. However, now my steering is a bit tight and no longer corrects itself/returns. If I turn right and let go of the wheel...
  6. Steering, Suspension, and Chassis
    Hey guys, been a while. I'll try to make this short and sweet. I have a 65 with a CPP Subframe kit, tubular upper and lower control arms. Tie rods, pitman arm and idler arm are all from a CPP rebuild kit. I also have a bearing conversion on the idler arm. Camber lock out kit installed. Problem...
  7. Steering, Suspension, and Chassis
    Hello new to the board and my 1st post! I have a 1968 Nova that im having worked on. Im having the steering converted to a power rack but the shop that im having the work done with is telling me the angle of the new rack is wrong, im starting to have my doubts about this shop but would i need...
  8. Steering, Suspension, and Chassis
    1964 Chevy II 4 door Just bought the car, steering knuckle was installed 90 degrees out, but the guy said it was all new front end parts. Took it to front end alignment, after string method failed me, they did it, drove it, then changed a lower ball joint. $$$ Then another alignment. But as I...
  9. Steering, Suspension, and Chassis
    Hi guys, I'm relatively new here, but I love the collaborative spirit. I am gearing up to start what is a big project for me and I'm hoping you guys could loan some of that "been there/done that" knowledge to me in preparation. I want to upgrade my 64 Chevy II suspension, brakes and steering...
  10. Steering, Suspension, and Chassis
    I have a back half 74 that I am going to make into a drag car. I am going to be changing out the 350 for a large BB, probably a 572. My question is... What are the advantages of an aftermarket front clip? I know there is a lot more room for everything with the new clip. They also have a...
  11. Steering, Suspension, and Chassis
    I'm swapping the manual steering to power. I've got a gear box supposedly from another 70 or 72 Nova. When I attempted to test fit it today its alignment to the column was a touch off. Meaning the gear box was pointed a touch high. Does anyone know if it is supposed to be or needs to be dead...
  12. Steering, Suspension, and Chassis
    I'm in the middle of rebuilding my steering column for my 69 non-tilt column. From taking it all apart, I see that some of the little parts could use some replacing. This weekend, the local Pick-a-part is having a 50% off sale, and I'm wondering what columns would have the same parts. I...
  13. Steering, Suspension, and Chassis
    Hey all, I purchased a power steering kit from CPP as well as an ididit column and am going to start removing the original manual box and column this weekend. I'm looking for any suggestions or tips that would help with the install...?? thanks in advance.
  14. 1st & 2nd Generation Chevy II/Nova's
    I am a newbie and hope this is the correct place to post this thread. I just wanted to share my experience improving my ride with a new CPP mini K-member front suspension upgrade that includes upper and lower tubular control arms. I also added a anti-sway bar to improve the cornering handling...
  15. Steering, Suspension, and Chassis
    Long story short while leaving work last night I lost most steering capabilities luckily it was 3am and no one was on the road I was able to make it back to my house without any damage to myself or the nova:yes: I feel very blessed. But now I'm not sure what to do rebuild the steering column or...
  16. Steering, Suspension, and Chassis
    Hi Nova Fans, I have a question that I cant seem to find an answer to, when I turn my steering wheel to the left I can feel it grab or bind and feel it click, I cant see anything thats binding up. Is their anywhere that you can grease it, a cert or anything? Had to put away and stop messing...
  17. Steering, Suspension, and Chassis
    Okay so i'm trying to get a plan of attack on "projects" for my 63 vert. i've read so much stuff on here :eek: and i'm trying to get some sort of ideas on what to do first or what should be done at the same time. here are my "ideas" :eek: Brakes first.... the car has manual drum brakes all...
  18. Steering, Suspension, and Chassis
    putting 85 montecarlo ss steering box on 68 nova -will i have to put different steering arm on -or will 68 arm still work..also can get 83 ss box cheaper -is this the same box and why is it never mentioned =only 85-88
  19. Drivetrain & Performance
    has anyone ever added A/C? i've found kits but just wanted some insight about it. Also, what's the process in adding power/disc brakes?? and has anyone ever added power steering??? i'm looking to get a 63 convertible........ thanks!
1-19 of 37 Results
Top