problems finding big block pulleys

I dragged my feet and did not order these parts last year, and now that I am ready to order them, several are discontinued. The crank and power steering are that are available.

So is anyone else in the same situation? If so, what are you using?

I need the alternator setup part # 4012-285-692S
big block pulleys:
crank pulley 4012-266-696
water pump pulley $ 34.95 ea 4012-269-693 (can't find out if this is a single or double groove, prefer single)
alternator pulley 4020-286-681
and power steering pulley 4012-288-693

thanks in advance

I bought all deep groove repops single groove water pump,double groove crank,and alt.I still have my power steering.

Hey Bill, Car show and swap meet at the Anoka county fairgrounds on saturday:D you might find the parts there:beer: One on sunday at the state fairgrounds also.

I bought all deep groove repops single groove water pump,double groove crank,and alt.I still have my power steering.

When and where did you buy these?

Tim, I am thinking about the show, depends on how far I get with my driveway extension :(

When and where did you buy these?

Tim, I am thinking about the show, depends on how far I get with my driveway extension :(

At www.early-birds.com I like the fact I can go right to the store if I want.They have a 1-800# as well on the site.

Does anyone know what the diameter on the crank pulley should be? I know a lot of the big block pulleys on the market will be too close to the crossmember, and would like to know what diameter should be on the nova big blocks. Thanks

check with NNN...just click on the top of the page or call 717-252-4192.

wilma:chev:

I bought all mine off of ebay

Yeah, don't get down though. They are definately still available. If not repop or at a swap meet etc.

Hell, if you can't find them anywhere PM me and I'll send you some from Canada haha :D

__________________

http://i128.photobucket.com/albums/p183/car_087/bottom6.jpg

Does anyone know what the diameter on the crank pulley should be? I know a lot of the big block pulleys on the market will be too close to the crossmember, and would like to know what diameter should be on the nova big blocks. Thanks

My deep groove is 7" in diameter,it's a 2 groove pulley.

My deep groove is 7" in diameter,it's a 2 groove pulley.

Taz, do you have the motor in the car? If so, how is the clearance to the frames crossmember?

thanks

Bill,
I also have a two groove pulley on my race car. No clearance issues.

I believe I ordered this one from Classic Industries. The part number is KW396. It is a two groove pulley. In their catalog it shows it's for a Big Block but online it shows small block.

Bill,
I also have a two groove pulley on my race car. No clearance issues.

I believe I ordered this one from Classic Industries. The part number is KW396. It is a two groove pulley. In their catalog it shows it's for a Big Block but online it shows small block.

Ron, I thought your crossmember was notched out in that area, or is it only the further back crossmember?

thanks again guys

Taz, do you have the motor in the car? If so, how is the clearance to the frames crossmember?

thanks

There is about 1/2"-3/4" clearance to the crossmember,yes motors in.I had a 3 groove ( it has a larger diameter for 1 groove) and it was hard to change the belt so I bought the 2 groove.No more problem.:D

Bill,
It's only notched by the oil pan. I had the same issues with the 3 groove that Taz mentioned so I switched to the two groove.

Thanks Ron and Taz, the two groove crank pulley it will be :)

http://cgi.ebay.com/ebaymotors/BIG-BLOCK-CHEVY-POWER-STEERING-BRACKET-SET-CHEVELLE_W0QQcmdZViewItemQQcategoryZ34202QQihZ005Q QitemZ150115380082QQrdZ1

http://cgi.ebay.com/ebaymotors/BIG-BLOCK-CHEVY-ALTERNATOR-BRACKETS-GM-CAMARO-CHEVELLE_W0QQcmdZViewItemQQcategoryZ140681QQihZ005 QQitemZ150115422110QQrdZ1